LegalizeCommission Implementing Regulation (EU) 2022/1434 of 22 July 2022 granting a Union authorisation for the biocidal product family ‘CMIT-MIT Aqueous 1.5-15’ (Text with EEA relevance)
— During handling phases (mixing and loading) and cleaning of the dispensing pumps, exposure to the product (corrosive and skin sensitizer product) has to be limited by use of PPE and application of technical and organisational RMM: — Minimisation of manual phases (process automation); — Use of a dosing device; — Regular cleaning of equipment and work area; — Avoidance of contact with contaminated tools and objects; — Good standard of general ventilation; — Training and management of staff on good practice.
— PPE is as follows: — protective chemical resistant gloves (glove material to be specified by the authorisation holder within the product information); — protective coverall (at least type 3 or 4, EN 14605) which is impermeable for the biocidal product shall be worn (coverall material to be specified by the authorisation holder within the product information); — Eye protection; — Substance/task appropriate respirator if ventilation is inadequate.
See general directions for use.
See general directions for use.
See general directions for use.
| Product type | PT11: Preservatives for liquid-cooling and processing systems |
|---|---|
| Where relevant, an exact description of the authorised use | - |
| Target organism(s) (including development stage) | Scientific name: no data Common name: Bacteria (anaerobes and aerobes (including Legionella pneumophila) Development stage: no data Scientific name: no data Common name: Yeasts Development stage: no data Scientific name: no data Common name: fungi Development stage: no data |
| Field(s) of use | indoor use outdoor use Preservation of liquids used in closed recirculating heating systems and associated pipework. Pre-commission biocide flushing of new or existing pipework systems (heating and chilling pipework) includes used or new structural pipework built on industrial building projects. Closed recirculating heating systems: pre-commission biocidal product flushing of new or existing pipework systems (heating and chilling pipework) includes used or new structural pipework built on industrial building projects. The biocidal product is used to control the growth of aerobic and anaerobic bacteria, fungi and biofilm in the circulating water of closed systems. Closed systems are less susceptible to corrosion, scaling and biological fouling than open systems. However microbial problems can occur, if the system is left filled and untreated. This is due to the presence of nitrite and glycols used as nutrients by microbes. |
| Application method(s) | Method: closed system Detailed description: Manual and automated dosing. The biocidal product is dosed automatically in the heat transfer fluid, in a place of good mixing. The feeding pipe must dose the biocidal product below the water level in order to limit the evaporation of the biocidal product. |
| Application rate(s) and frequency | Application Rate: Curative treatment - against bacteria at 5 g C(M)IT/MIT (3:1) / m3 of water (including L. pneumophila) - against biofilm at 14,9 g C(M)IT/MIT (3:1) / m3 of water - against fungi and yeast at 1 g C(M)IT/MIT / m3 of water Preventive treatment - against bacteria (including L. pneumophila) at 3 g C(M)IT/MIT (3:1) / m3 of water - against biofilm at 3 g C(M)IT/MIT (3:1) / m3 of water. - Number and timing of application: Curative treatment: — against bacteria at 5 g C(M)IT/MIT (3:1) / m3 of water (including L. pneumophila) Contact time: 24 hours — against biofilm at 14,9 g C(M)IT/MIT (3:1) / m3 of water Contact time: 24 hours — against fungi and yeast at 1 g C(M)IT/MIT / m3 of water Contact time: 48 hours Preventive treatment — against bacteria (including L. pneumophila) at 3 g C(M)IT/MIT (3:1) / m3 of water and against biofilm at 3 g C(M)IT/MIT (3:1) / m3 of water. |
| Category(ies) of users | industrial |
| Pack sizes and packaging material | For industrial and professional users: — HDPE flask: 5 L (nominal) — HDPE Pail / Jerrycan: 10 L, 20 L, 25 L, 30 L (nominal) — Box with HDPE liner: 20 L — HDPE Drum: 110 L, 120 L, 200 L, 260 L — HDPE IBC: 650 L, 800 L, 1 000 L, 1 250 L All products should be transport and stored in a vented room. |
Microbiological tests to prove adequacy of preservation have to be undertaken by the user of C(M)IT/MIT products in order to determine the effective dose of the preservative for the specific matrix/location/system. If needed, consult the manufacturer of the preservative product.
— Rinse the system (especially the dispensing pumps) with water prior to perform the cleaning step.
— During handling phases (mixing and loading) and cleaning of the dispensing pumps, exposure to the product (corrosive and skin sensitizer product) has to be limited by use of PPE and application of technical and organisational RMM: — Minimisation of manual phases (process automation); — Use of a dosing device; — Regular cleaning of equipment and work area; — Avoidance of contact with contaminated tools and objects; — Good standard of general ventilation; — Training and management of staff on good practice.
— PPE is as follows: — protective chemical resistant gloves (glove material to be specified by the authorisation holder within the product information); — protective coverall (at least type 3 or 4, EN 14605) which is impermeable for the biocidal product shall be worn (coverall material to be specified by the authorisation holder within the product information); — Eye protection; — Substance/task appropriate respirator if ventilation is inadequate.
See general directions for use.
See general directions for use.
See general directions for use.
| Product type | PT11: Preservatives for liquid-cooling and processing systems |
|---|---|
| Where relevant, an exact description of the authorised use | - |
| Target organism(s) (including development stage) | Scientific name: no data Common name: Bacteria Development stage: no data |
| Field(s) of use | outdoor use Preservation of polymers used in oilfield processes (e.g. enhanced oil recovery, drilling muds, etc.) |
| Application method(s) | Method: - Detailed description: - |
| Application rate(s) and frequency | Application Rate: Preventive treatment of polymers used in the injection water: Xanthan polymer: 30 -50 g C(M)IT/MIT/m3 solution. HPAM polymer: 30 - 50 g C(M)IT/MIT/m3 solution. Preventive treatment of polymers used in the drilling muds: Xanthan polymer: 30 g C(M)IT/MIT/m3 solution. HPAM polymer: 30 g C(M)IT/MIT/m3 solution. - Number and timing of application: Preventive treatment of polymers used in the injection water: Xanthan polymer: 30 -50 g C(M)IT/MIT/m3 solution. HPAM polymer: 30 - 50 g C(M)IT/MIT/m3 solution. Preventive treatment of polymers used in the drilling muds: Xanthan polymer: 30 g C(M)IT/MIT/m3 solution. HPAM polymer: 30 g C(M)IT/MIT/m3 solution. |
| Category(ies) of users | industrial |
| Pack sizes and packaging material | For industrial and professional users: — HDPE flask: 5 L (nominal) — HDPE Pail / Jerrycan: 10 L, 20 L, 25 L, 30 L (nominal) — Box with HDPE liner: 20 L — HDPE Drum: 110 L, 120 L, 200 L, 260 L — HDPE IBC: 650 L, 800 L, 1 000 L, 1 250 L All products should be transport and stored in a vented room. |
Microbiological tests to prove adequacy of preservation have to be undertaken by the user of C(M)IT/MIT products in order to determine the effective dose of the preservative for the specific matrix/location/system. If needed, consult the manufacturer of the preservative product.
— Rinse the system (especially the dispensing pumps) with water prior to perform the cleaning step.
— During handling phases (mixing and loading) and cleaning of the dispensing pumps, exposure to the product (corrosive and skin sensitizer product) has to be limited by use of PPE and application of technical and organisational RMM: — Minimisation of manual phases (process automation); — Use of a dosing device; — Regular cleaning of equipment and work area; — Avoidance of contact with contaminated tools and objects; — Good standard of general ventilation; — Training and management of staff on good practice.
— PPE is as follows: — protective chemical resistant gloves (glove material to be specified by the authorisation holder within the product information); — protective coverall (at least type 3 or 4, EN 14605) which is impermeable for the biocidal product shall be worn (coverall material to be specified by the authorisation holder within the product information); — Eye protection; — Substance/task appropriate respirator if ventilation is inadequate.
See general directions for use.
See general directions for use.
See general directions for use.
| Product type | PT12: Slimicides |
|---|---|
| Where relevant, an exact description of the authorised use | - |
| Target organism(s) (including development stage) | Scientific name: no data Common name: Bacteria Development stage: no data Scientific name: no data Common name: Yeasts Development stage: no data Scientific name: no data Common name: fungi Development stage: no data |
| Field(s) of use | indoor use Slimicide treatment in the de-inking process of the pulp and paper. Recycling paper /deinking paper mills. Deinking process is a manufacturing paper process of removing printing inks from waste paper-fibers to produce deinked pulp. |
| Application method(s) | Method: closed system Detailed description: Manual and automated dosing. The biocidal product is automatically dosed by pump and fixed pipes into the circuit, usually in the pulper below the water level. |
| Application rate(s) and frequency | Application Rate: Curative treatment: 10 to 14,9 g C(M)IT/MIT (3:1) / m3 of water to be treated. Preventive treatment: 5 g C(M)IT/MIT (3:1) / m3 of water to be treated. - Number and timing of application: Curative treatment: 10 to 14,9 g C(M)IT/MIT (3:1) / m3 of water to be treated Contact time: 24 hours Preventive treatment: 5 g C(M)IT/MIT (3:1) / m3 of water to be treated. |
| Category(ies) of users | industrial |
| Pack sizes and packaging material | For industrial and professional users: — HDPE flask: 5 L (nominal) — HDPE Pail / Jerrycan: 10 L, 20 L, 25 L, 30 L (nominal) — Box with HDPE liner: 20 L — HDPE Drum: 110 L, 120 L, 200 L, 260 L — HDPE IBC: 650 L, 800 L, 1 000 L, 1 250 L All products should be transport and stored in a vented room. |
Microbiological tests to prove adequacy of preservation have to be undertaken by the user of C(M)IT/MIT products in order to determine the effective dose of the preservative for the specific matrix/location/system. If needed, consult the manufacturer of the preservative product.
— Rinse the system (especially the dispensing pumps) with water prior to perform the cleaning step.
— During handling phases (mixing and loading) and cleaning of the dispensing pumps, exposure to the product (corrosive and skin sensitizer product) has to be limited by use of PPE and application of technical and organisational RMM: — Minimisation of manual phases (process automation); — Use of a dosing device; — Regular cleaning of equipment and work area; — Avoidance of contact with contaminated tools and objects; — Good standard of general ventilation; — Training and management of staff on good practice.
— PPE is as follows: — protective chemical resistant gloves (glove material to be specified by the authorisation holder within the product information); — protective coverall (at least type 3 or 4, EN 14605) which is impermeable for the biocidal product shall be worn (coverall material to be specified by the authorisation holder within the product information); — Eye protection; — Substance/task appropriate respirator if ventilation is inadequate.
See general directions for use.
See general directions for use.
See general directions for use.
| Product type | PT12: Slimicides |
|---|---|
| Where relevant, an exact description of the authorised use | - |
| Target organism(s) (including development stage) | Scientific name: no data Common name: Bacteria Development stage: no data Scientific name: no data Common name: Yeasts Development stage: no data Scientific name: no data Common name: fungi Development stage: no data |
| Field(s) of use | indoor use Slimicide treatment in the wet-end stage of the paper manufacturing process (paper mills, wet-end stage (water circuits), and paper mills process system). |
| Application method(s) | Method: closed system Detailed description: Manual and automated dosing. |
| Application rate(s) and frequency | Application Rate: Curative treatment: 10 to 14,9 g C(M)IT/MIT (3:1) / m3 of water to be treated. Preventive treatment: 5 g C(M)IT/MIT (3:1) / m3 of water to be treated. - Number and timing of application: Curative treatment: 10 to 14,9 g C(M)IT/MIT (3:1) / m3 of water to be treated Contact time: 24 hours Preventive treatment: 5 g C(M)IT/MIT (3:1) / m3 of water to be treated. |
| Category(ies) of users | industrial |
| Pack sizes and packaging material | For industrial and professional users: — HDPE flask: 5 L (nominal) — HDPE Pail / Jerrycan: 10 L, 20 L, 25 L, 30 L (nominal) — Box with HDPE liner: 20 L — HDPE Drum: 110 L, 120 L, 200 L, 260 L — HDPE IBC: 650 L, 800 L, 1 000 L, 1 250 L All products should be transport and stored in a vented room. |
Microbiological tests to prove adequacy of preservation have to be undertaken by the user of C(M)IT/MIT products in order to determine the effective dose of the preservative for the specific matrix/location/system. If needed, consult the manufacturer of the preservative product.
— Rinse the system (especially the dispensing pumps) with water prior to perform the cleaning step.
— During handling phases (mixing and loading) and cleaning of the dispensing pumps, exposure to the product (corrosive and skin sensitizer product) has to be limited by use of PPE and application of technical and organisational RMM: — Minimisation of manual phases (process automation); — Use of a dosing device; — Regular cleaning of equipment and work area; — Avoidance of contact with contaminated tools and objects; — Good standard of general ventilation; — Training and management of staff on good practice.
— PPE is as follows: — protective chemical resistant gloves (glove material to be specified by the authorisation holder within the product information); — protective coverall (at least type 3 or 4, EN 14605) which is impermeable for the biocidal product shall be worn (coverall material to be specified by the authorisation holder within the product information); — Eye protection; — Substance/task appropriate respirator if ventilation is inadequate.
— The use of C(M)IT/MIT (3:1) containing products for the slimicide treatment in the wet-end stage of the paper manufacturing process is restricted to (a) curative treatments in plants connected to a slimicide-free water from a pulp mill and only for the treatment of the short circulation of the paper mill; and (b) preventive treatments, and, for both cases, only if the factory’s waste water is purified in an on-site (full) industrial sewage treatment plant with a minimal capacity of 5 000 m3 per day as described in the Industrial Emission Directive 2010/75/EU (Best Available Techniques for the production of pulp, paper and board) and if a dilution of at least 200 times in surface water is achieved after the industrial sewage treatment plant.
See general directions for use.
See general directions for use.
See general directions for use.
| Product type | PT12: Slimicides |
|---|---|
| Where relevant, an exact description of the authorised use | - |
| Target organism(s) (including development stage) | Scientific name: no data Common name: Bacteria Development stage: no data |
| Field(s) of use | indoor use Preventive treatment (biofouling control) online and after cleaning in place for industrial RO/NF membranes |
| Application method(s) | Method: closed system Detailed description: Manual and automated dosing.Biocidal product application on a routine basis will prevent biofilm growth on Reverse Osmosis or Nano Filtration membrane surfaces, feed spacer, filter media and pipework. The biocidal product should be dispensed to the feed water at a point to assure adequate mixing throughout the system. |
| Application rate(s) and frequency | Application Rate: Preventive treatment: 5 g C(M)IT/MIT (3:1) per m3 of fluid - Number and timing of application: Preventive treatment: 5 g C(M)IT/MIT (3:1) per m3 of fluid |
| Category(ies) of users | industrial |
| Pack sizes and packaging material | For industrial and professional users: — HDPE flask: 5 L (nominal) — HDPE Pail / Jerrycan: 10 L, 20 L, 25 L, 30 L (nominal) — Box with HDPE liner: 20 L — HDPE Drum: 110 L, 120 L, 200 L, 260 L — HDPE IBC: 650 L, 800 L, 1 000 L, 1 250 L All products should be transport and stored in a vented room. |
Microbiological tests to prove adequacy of preservation have to be undertaken by the user of C(M)IT/MIT products in order to determine the effective dose of the preservative for the specific matrix/location/system. If needed, consult the manufacturer of the preservative product.
— Rinse the system (especially the dispensing pumps) with water prior to perform the cleaning step.
— During handling phases (mixing and loading) and cleaning of the dispensing pumps, exposure to the product (corrosive and skin sensitizer product) has to be limited by use of PPE and application of technical and organisational RMM: — Minimisation of manual phases (process automation); — Use of a dosing device; — Regular cleaning of equipment and work area; — Avoidance of contact with contaminated tools and objects; — Good standard of general ventilation; — Training and management of staff on good practice.
— PPE is as follows: — protective chemical resistant gloves (glove material to be specified by the authorisation holder within the product information); — protective coverall (at least type 3 or 4, EN 14605) which is impermeable for the biocidal product shall be worn (coverall material to be specified by the authorisation holder within the product information); — Eye protection; — Substance/task appropriate respirator if ventilation is inadequate.
— Use product only in premises that are connected to a STP.
See general directions for use.
See general directions for use.
See general directions for use.
| Product type | PT13: Working or cutting fluid preservatives |
|---|---|
| Where relevant, an exact description of the authorised use | - |
| Target organism(s) (including development stage) | Scientific name: no data Common name: Bacteria Development stage: no data Scientific name: no data Common name: Yeasts Development stage: no data Scientific name: no data Common name: fungi Development stage: no data |
| Field(s) of use | indoor use Products to control microbial deterioration in fluids used for working or cutting metal, glass or other materials The biocidal product is recommended to control the growth of bacteria and fungi in fluids used for metalworking fluids (cutting, grinding, rolling, drawing, etc.) metal surface treatment (aqueous multipurpose and de-watering rust cleaner fluids, etc.) and cutting fluids for glass or other materials. |
| Application method(s) | Method: - Detailed description: The biocidal product should be dispensed as a tankside additive into the circulating use-dilution of the fluid, using a metering pump or by manual pouring, at a point to assure adequate mixing throughout the system. |
| Application rate(s) and frequency | Application Rate: Curative treatment: When the system is noticeably fouled, apply 14,9 g C(M)IT/MIT (3:1) per m3 of fluid to be treated. Preventive treatment: When control is obtained, adding 10 g C(M)IT/MIT (3:1) per m3 of fluid to be treated. - Number and timing of application: Curative treatment: When the system is noticeably fouled, apply 14,9 g C(M)IT/MIT (3:1) per m3 of fluid to be treated. Contact time: 24h Preventive treatment: When control is obtained, adding 10 g C(M)IT/MIT (3:1) per m3 of fluid to be treated. |
| Category(ies) of users | industrial |
| Pack sizes and packaging material | For industrial and professional users: — HDPE flask: 5 L (nominal) — HDPE Pail / Jerrycan: 10 L, 20 L, 25 L, 30 L (nominal) — Box with HDPE liner: 20 L — HDPE Drum: 110 L, 120 L, 200 L, 260 L — HDPE IBC: 650 L, 800 L, 1 000 L, 1 250 L All products should be transport and stored in a vented room. |
Microbiological tests to prove adequacy of preservation have to be undertaken by the user of C(M)IT/MIT products in order to determine the effective dose of the preservative for the specific matrix/location/system. If needed, consult the manufacturer of the preservative product.
— Rinse the system (especially the dispensing pumps) with water prior to perform the cleaning step.
— During handling phases (mixing and loading) and cleaning of the dispensing pumps, exposure to the product (corrosive and skin sensitizer product) has to be limited by use of PPE and application of technical and organisational RMM: — Minimisation of manual phases (process automation); — Use of a dosing device; — Regular cleaning of equipment and work area; — Avoidance of contact with contaminated tools and objects; — Good standard of general ventilation; — Training and management of staff on good practice.
— PPE is as follows: — protective chemical resistant gloves (glove material to be specified by the authorisation holder within the product information); — protective coverall (at least type 3 or 4, EN 14605) which is impermeable for the biocidal product shall be worn (coverall material to be specified by the authorisation holder within the product information); — Eye protection; — Substance/task appropriate respirator if ventilation is inadequate.
See general directions for use.
See general directions for use.
See general directions for use.
5. GENERAL DIRECTIONS FOR USE OF THE META SPC 3
— The duration of the effect is dependent on the performance requirements of the customer for their preserved material and on the specific ingredients composition and pH of the preserved product.
— Always read the label or leaflet before use and follow all the instructions provided.
— Respect the conditions of use of the product (concentration, contact time, temperature, pH, etc.)
PRECAUTIONARY MEASURES DURING STORAGE AND TRANSPORT:
Keep in a well-ventilated place. The product as supplied may evolve gas (largely carbon dioxide) slowly. To prevent the buildup of pressure the product is packaged in specially vented containers, where necessary. Keep this product in the original container when not in use. Container must be stored and transported in an upright position to prevent spilling the contents through the vent, where fitted.
-
— Skin contact: Remove contaminated clothing and shoes. Wash contaminated skin with water. Contact poison treatment specialist if symptoms occur.
— Eye contact: Immediately flush with plenty of water, occasionally lifting the upper and lower eyelids. Check for and remove any contact lenses if easy to do. Continue to rinse with tepid water for at least 30 minutes. Call 112/ambulance for medical assistance.
— Ingestion: Wash out mouth with water. Contact poison treatment specialist. Seek medical advice immediately if symptoms occur and/or large quantities have been ingested. Do not give fluids or induce vomiting.
— Inhalation (of spray mist): Remove victim to fresh air and keep at rest in a position comfortable for breathing. Seek medical advice immediately if symptoms occur and/or large quantities have been inhaled.
— In case of impaired consciousness place in recovery position and seek medical advice immediately.
— Keep the container or label available.
— Do not discharge unused product on the ground, into water courses, into pipes (e.g. sink, toilets) nor down the drains.
— Dispose of unused product, its packaging and all other waste, in accordance with local regulations.
Conditions for safe storage, including any incompatibilities: Keep in a dry, cool and well-ventilated place, in the original container.
Shelf-life: 12 months
Protect from sunlight.
Recommendation: If a metal packaging is used, a varnish layer should be applied.
6. OTHER INFORMATION
-
7. THIRD INFORMATION LEVEL: INDIVIDUAL PRODUCTS IN THE META SPC 3
| Trade name(s) | KATHON™ CF 400 Biocide | Market area: EU | |||
|---|---|---|---|---|---|
| Dab 4228 | Market area: EU | ||||
| BAL 400BI | Market area: EU | ||||
| Biocide 400 | Market area: EU | ||||
| Biotech 400 | Market area: EU | ||||
| Biocide KT400 | Market area: EU | ||||
| BioCheck KT400 | Market area: EU | ||||
| KT400 | Market area: EU | ||||
| C 412 TT | Market area: EU | ||||
| Dab 4228 | Market area: EU | ||||
| Deep Bio® 400 | Market area: EU | ||||
| Ecosafe Bio 400 | Market area: EU | ||||
| Filtralga ME | Market area: EU | ||||
| Filtralga 9550 | Market area: EU | ||||
| PH-SB400 | Market area: EU | ||||
| Helamin BZ9550 | Market area: EU | ||||
| Isotreat 400 | Market area: EU | ||||
| OS Isobio4 | Market area: EU | ||||
| Odysside B 330 | Market area: EU | ||||
| Relvamine BIOC | Market area: EU | ||||
| Sayvol Bio LP400 | Market area: EU | ||||
| Authorisation number | EU-0025449-0004 1-3 | ||||
| Common name | IUPAC name | Function | CAS number | EC number | Content (%) |
| C(M)IT/MIT (3:1) | Reaction mass of 5-chloro-2-methyl-2h-isothiazol-3-one and 2-methyl-2h-isothiazol-3-one (3:1) | Active substance | 55965-84-9 | 5,9 % (w/w) | |
| Trade name(s) | KATHON™CF 210 BIOCIDE | Market area: EU | |||
| --- | --- | --- | --- | --- | --- |
| BAL 210BI | Market area: EU | ||||
| BioCheck KT210 | Market area: EU | ||||
| Biocide KT210 | Market area: EU | ||||
| Biocide 210 | Market area: EU | ||||
| Biotech 210 | Market area: EU | ||||
| B203-210 | Market area: EU | ||||
| Deep Bio® 210 | Market area: EU | ||||
| Ecosafe Bio 210 | Market area: EU | ||||
| Filtralga ME-15 | Market area: EU | ||||
| KT210 | Market area: EU | ||||
| Isotreat 210 | Market area: EU | ||||
| MIRECIDE-M/86 | Market area: EU | ||||
| MK3203 | Market area: EU | ||||
| MK3094 | Market area: EU | ||||
| MK3394 | Market area: EU | ||||
| OS Isobio 210 | Market area: EU | ||||
| Odysside B 330M | Market area: EU | ||||
| PH-SB210 | Market area: EU | ||||
| STENCO B-85 | Market area: EU | ||||
| Sayvol Bio LP210 | Market area: EU | ||||
| TECNA 520 | Market area: EU | ||||
| Authorisation number | EU-0025449-0005 1-3 | ||||
| Common name | IUPAC name | Function | CAS number | EC number | Content (%) |
| C(M)IT/MIT (3:1) | Reaction mass of 5-chloro-2-methyl-2h-isothiazol-3-one and 2-methyl-2h-isothiazol-3-one (3:1) | Active substance | 55965-84-9 | 3,2 % (w/w) | |
| Trade name(s) | KATHON™WT 210 BIOCIDE | Market area: EU | |||
| --- | --- | --- | --- | --- | --- |
| A-CID SA | Market area: EU | ||||
| ADUR 166 | Market area: EU | ||||
| ALG 200 | Market area: EU | ||||
| Biocide BALK 20 | Market area: EU | ||||
| Biocide KT210WT | Market area: EU | ||||
| France Algue 242 | Market area: EU | ||||
| KL60 TA21 | Market area: EU | ||||
| KT210WT | Market area: EU | ||||
| MK3094 | Market area: EU | ||||
| MK3394 | Market area: EU | ||||
| MK3203 | Market area: EU | ||||
| B203-210WT | Market area: EU | ||||
| Biocide 210WT | Market area: EU | ||||
| Biotech 210WT | Market area: EU | ||||
| Deep Bio® 210WT | Market area: EU | ||||
| Ecosafe Bio 210WT | Market area: EU | ||||
| OS Isobio 210WT | Market area: EU | ||||
| PH-SB210WT | Market area: EU | ||||
| Sayvol Bio LP210WT | Market area: EU | ||||
| Authorisation number | EU-0025449-0006 1-3 | ||||
| Common name | IUPAC name | Function | CAS number | EC number | Content (%) |
| C(M)IT/MIT (3:1) | Reaction mass of 5-chloro-2-methyl-2h-isothiazol-3-one and 2-methyl-2h-isothiazol-3-one (3:1) | Active substance | 55965-84-9 | 3,2 % (w/w) | |
| Trade name(s) | KATHON™ WTE BIOCIDE | Market area: EU | |||
| --- | --- | --- | --- | --- | --- |
| KATHON™ WTE | Market area: EU | ||||
| KATHON™ LXE BIOCIDE | Market area: EU | ||||
| KATHON™ LXE | Market area: EU | ||||
| KATHON™ MWE BIOCIDE | Market area: EU | ||||
| Bansan 150 | Market area: EU | ||||
| Biocide KT200LX | Market area: EU | ||||
| Biocide KT200WT | Market area: EU | ||||
| Biocide KT200MW | Market area: EU | ||||
| Biocide 515WTE | Market area: EU | ||||
| Biocide 515 MW | Market area: EU | ||||
| Biotech 103WTE | Market area: EU | ||||
| BioCheck WTE | Market area: EU | ||||
| BioCheck KT MW | Market area: EU | ||||
| Biocheck WB | Market area: EU | ||||
| Biocheck 3103 | Market area: EU | ||||
| Biotech 103MW | Market area: EU | ||||
| BIOMATE SAN9363 | Market area: EU | ||||
| BIO 417 | Market area: EU | ||||
| B203WTE | Market area: EU | ||||
| B203MW | Market area: EU | ||||
| C 412 TTE | Market area: EU | ||||
| Deep Bio® 20MW | Market area: EU | ||||
| Deep Bio® 20WTE | Market area: EU | ||||
| Ecosafe Bio WTE | Market area: EU | ||||
| Ecosafe Bio MW | Market area: EU | ||||
| Hydrex™ 7310 | Market area: EU | ||||
| Isotreat WTE | Market area: EU | ||||
| KT200LX | Market area: EU | ||||
| KT200WT | Market area: EU | ||||
| KT200MW | Market area: EU | ||||
| MIRECIDE-M/87 | Market area: EU | ||||
| Novocide 10 C | Market area: EU | ||||
| OBBIO210 | Market area: EU | ||||
| OS Isobio 1.5WTE | Market area: EU | ||||
| Pastosept K | Market area: EU | ||||
| PH-SB102WTE | Market area: EU | ||||
| PH-SB102MW | Market area: EU | ||||
| PS 2175 | Market area: EU | ||||
| SAN ADDITIVE | Market area: EU | ||||
| SANY POOL | Market area: EU | ||||
| Sayvol Bio WTE | Market area: EU | ||||
| Sayvol Bio LP MW | Market area: EU | ||||
| Wacozid 3150 | Market area: EU | ||||
| OS Isobio 1.5MW | Market area: EU | ||||
| BAC-S | Market area: EU | ||||
| Biocide BAL GX | Market area: EU | ||||
| Biocide BAL P10 | Market area: EU | ||||
| Biocide BALK 10 | Market area: EU | ||||
| biocil-I | Market area: EU | ||||
| BIOMATE MBC781 | Market area: EU | ||||
| France Algue 222 | Market area: EU | ||||
| GEWA B 352 | Market area: EU | ||||
| HCT-B-71 | Market area: EU | ||||
| O’RIZON 415 | Market area: EU | ||||
| rascal-B-71 | Market area: EU | ||||
| WANSON W23L | Market area: EU | ||||
| watERTreat BIO253 B | Market area: EU | ||||
| Authorisation number | EU-0025449-0007 1-3 | ||||
| Common name | IUPAC name | Function | CAS number | EC number | Content (%) |
| C(M)IT/MIT (3:1) | Reaction mass of 5-chloro-2-methyl-2h-isothiazol-3-one and 2-methyl-2h-isothiazol-3-one (3:1) | Active substance | 55965-84-9 | 2,3 % (w/w) | |
| Trade name(s) | KATHON™ CF 150 Biocide | Market area: EU | |||
| --- | --- | --- | --- | --- | --- |
| KATHON™ CF-150 Biocide | Market area: EU | ||||
| KATHON™ CF-150 | Market area: EU | ||||
| AAHS BI | Market area: EU | ||||
| ACN Green Line 802 | Market area: EU | ||||
| AQ 616 | Market area: EU | ||||
| AQF 415 | Market area: EU | ||||
| AQUATREAT 415 | Market area: EU | ||||
| ATN JB48 | Market area: EU | ||||
| BAL 200BI | Market area: EU | ||||
| Bewacid B 728 | Market area: EU | ||||
| Biocheck WB CF | Market area: EU | ||||
| Biocheck 3103 CF | Market area: EU | ||||
| Biocide 515 | Market area: EU | ||||
| Biocide KT200 | Market area: EU | ||||
| BioCheck KT | Market area: EU | ||||
| BIOCONTROL 5 | Market area: EU | ||||
| BIOMATE MBC781E | Market area: EU | ||||
| BiopleX TZ 150 | Market area: EU | ||||
| Bio-Safe KT200 | Market area: EU | ||||
| Biotech 103 | Market area: EU | ||||
| B203 | Market area: EU | ||||
| BW 415 | Market area: EU | ||||
| BS4005A | Market area: EU | ||||
| Busan 1078 | Market area: EU | ||||
| Butrol 1078 | Market area: EU | ||||
| Bulab 8862 | Market area: EU | ||||
| Bulab 6057 | Market area: EU | ||||
| Carillion ITA | Market area: EU | ||||
| Certi-KT200 | Market area: EU | ||||
| CH32 | Market area: EU | ||||
| ComChem Bio ITA | Market area: EU | ||||
| Dab 448 | Market area: EU | ||||
| Deep Bio® 20 | Market area: EU | ||||
| DIABICIDE 90 A | Market area: EU | ||||
| DIPOLIQUE 156 | Market area: EU | ||||
| Ecoral 1015 | Market area: EU | ||||
| Ecosafe Bio WT | Market area: EU | ||||
| Ekobio-5 | Market area: EU | ||||
| ES515 | Market area: EU | ||||
| FINEALGUA ME | Market area: EU | ||||
| GE32 | Market area: EU | ||||
| Hydrex™ 7943 | Market area: EU | ||||
| HCS B32 | Market area: EU | ||||
| In-Boi | Market area: EU | ||||
| Isocil® Ultra 1.5 | Market area: EU | ||||
| Isotreat | Market area: EU | ||||
| IWT KT200 | Market area: EU | ||||
| KT200 | Market area: EU | ||||
| Lubron BD 100 | Market area: EU | ||||
| Lubron BD 110 | Market area: EU | ||||
| Lubron BD 120 | Market area: EU | ||||
| MB 215 | Market area: EU | ||||
| Mikrobizid M 24 | Market area: EU | ||||
| MIRECIDE-KW/600 | Market area: EU | ||||
| MIRECIDE-KW/600.X | Market area: EU | ||||
| Novocide 10 | Market area: EU | ||||
| Novo Cide 10 | Market area: EU | ||||
| NW515 | Market area: EU | ||||
| OS Isobio 1.5 | Market area: EU | ||||
| PA32 | Market area: EU | ||||
| PH-SB102 | Market area: EU | ||||
| PS 2176 | Market area: EU | ||||
| QUIPROISO LG | Market area: EU | ||||
| RAL200 | Market area: EU | ||||
| Relcide 310 | Market area: EU | ||||
| Sayvol Bio LP | Market area: EU | ||||
| ST202 | Market area: EU | ||||
| Starcide Ultra 1.5 | Market area: EU | ||||
| Swiftclean BI | Market area: EU | ||||
| UPINZOL -10 | Market area: EU | ||||
| Wacozid 3150 | Market area: EU | ||||
| Wacozid 3150 CF | Market area: EU | ||||
| Watercare WHM KT200 | Market area: EU | ||||
| “hygel“ KW 60 B | Market area: EU | ||||
| BioCheck KT200 | Market area: EU | ||||
| Authorisation number | EU-0025449-0008 1-3 | ||||
| Common name | IUPAC name | Function | CAS number | EC number | Content (%) |
| C(M)IT/MIT (3:1) | Reaction mass of 5-chloro-2-methyl-2h-isothiazol-3-one and 2-methyl-2h-isothiazol-3-one (3:1) | Active substance | 55965-84-9 | 2,3 % (w/w) | |
| Trade name(s) | KATHON™ CG/ICP Biocide | Market area: EU | |||
| --- | --- | --- | --- | --- | --- |
| KATHON™ CG-ICP | Market area: EU | ||||
| KATHON™ CG/ICP Preservative | Market area: EU | ||||
| KATHON™ MK Biocide | Market area: EU | ||||
| Biocide KT200ICP | Market area: EU | ||||
| Biogat CG ICP | Market area: EU | ||||
| Isocil® HP 1.5 | Market area: EU | ||||
| MIRECIDE-KW/24 | Market area: EU | ||||
| Authorisation number | EU-0025449-0009 1-3 | ||||
| Common name | IUPAC name | Function | CAS number | EC number | Content (%) |
| C(M)IT/MIT (3:1) | Reaction mass of 5-chloro-2-methyl-2h-isothiazol-3-one and 2-methyl-2h-isothiazol-3-one (3:1) | Active substance | 55965-84-9 | 2,2 % (w/w) | |
| Trade name(s) | KATHON™ CG/ICPII Biocide | Market area: EU | |||
| --- | --- | --- | --- | --- | --- |
| Authorisation number | EU-0025449-0010 1-3 | ||||
| Common name | IUPAC name | Function | CAS number | EC number | Content (%) |
| C(M)IT/MIT (3:1) | Reaction mass of 5-chloro-2-methyl-2h-isothiazol-3-one and 2-methyl-2h-isothiazol-3-one (3:1) | Active substance | 55965-84-9 | 2,2 % (w/w) | |
| Trade name(s) | KATHON™ CL 150 Biocide | Market area: EU | |||
| --- | --- | --- | --- | --- | --- |
| SPECTRUS NX1164 | Market area: EU | ||||
| Authorisation number | EU-0025449-0011 1-3 | ||||
| Common name | IUPAC name | Function | CAS number | EC number | Content (%) |
| C(M)IT/MIT (3:1) | Reaction mass of 5-chloro-2-methyl-2h-isothiazol-3-one and 2-methyl-2h-isothiazol-3-one (3:1) | Active substance | 55965-84-9 | 2,2 % (w/w) |
1. META SPC 4 ADMINISTRATIVE INFORMATION
| Identifier | Meta SPC: meta-SPC 4 KATHON 1.5-3.5 Na |
|---|---|
| Number | 1-4 |
| --- | --- |
| Product type(s) | PT02: Disinfectants and algaecides not intended for direct application to humans or animals PT04: Food and feed area PT06: Preservatives for products during storage PT11: Preservatives for liquid-cooling and processing systems PT12: Slimicides |
| --- | --- |
2. META SPC 4 COMPOSITION
| Common name | IUPAC name | Function | CAS number | EC number | Content (%) |
|---|---|---|---|---|---|
| C(M)IT/MIT (3:1) | Reaction mass of 5-chloro-2-methyl-2h-isothiazol-3-one and 2-methyl-2h-isothiazol-3-one (3:1) | Active substance | 55965-84-9 | 2,2 - 5,1 % (w/w) | |
| Formulation type(s) | AL Any other liquid | ||||
| --- | --- |
3. HAZARD AND PRECAUTIONARY STATEMENTS OF THE META SPC 4
| Hazard statements | H332: Harmful if inhaled. H314: Causes severe skin burns and eye damage. H317: May cause an allergic skin reaction. H410: Very toxic to aquatic life with long lasting effects. H302: Harmful if swallowed. EUH071: Corrosive to the respiratory tract. |
|---|---|
| Precautionary statements | P260: Do not breathe fume. P264: Wash skin thoroughly after handling. P270: Do not eat, drink or smoke when using this product. P272: Contaminated work clothing should not be allowed out of the workplace. P273: Avoid release to the environment. P280: Wear protective gloves/ protective clothing/ eye protection/ face protection/ hearing protection . P362+P364: Take off contaminated clothing and wash it before reuse. P333+P313: If skin irritation or rash occurs: Get medical advice. P301+P330+P331: IF SWALLOWED: rinse mouth. Do NOT induce vomiting. P303+P361+P353: IF ON SKIN (or hair): Take off immediately all contaminated clothing. Rinse skin with water [or shower]. P304+P340: IF INHALED: Remove person to fresh air and keep comfortable for breathing. P310: Immediately call a POISON CENTER/ doctor . P305+P351+P338: IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. P391: Collect spillage. P405: Store locked up. P301+P312: IF SWALLOWED: Call a POISON CENTER/ doctor if you feel unwell. |
4. AUTHORISED USE(S) OF THE META SPC
| Product type | PT02: Disinfectants and algaecides not intended for direct application to humans or animals |
|---|---|
| Where relevant, an exact description of the authorised use | - |
| Target organism(s) (including development stage) | Scientific name: no data Common name: Bacteria (including Legionella pneumophila) Development stage: no data Scientific name: no data Common name: Yeasts Development stage: no data Scientific name: no data Common name: fungi Development stage: no data Scientific name: no data Common name: algae Development stage: no data |
| Field(s) of use | outdoor use Preservation of sump water in air conditioning and air washer systems. Air conditioning systems and in air washer systems to preserve the sump water. Air washer systems are used extensively in textile factories and in the tobacco industry to scrub or clean the air and for fine control of temperature and humidity. |
| Application method(s) | Method: Open and closed Systems Detailed description: Automatic and Manual Dosing The biocidal product is typically added in a central chilled water sump which supplies several air washers. The loading process may be conducted either manually or by automation. In the automated process, the biocide is metered directly into the sump from a holding tank or other type of bulk container by a dosimeter (pump). The feeding pipe must dose the biocidal product below the water level in order to limit its evaporation. |
| Application rate(s) and frequency | Application Rate: Curative application: Bacteria, yeasts and fungi. When the system is noticeably fouled, apply 5 to 14,9 mg C(M)IT/MIT (3:1) per Litre of water to be treated, as post treatment after a shock dose of minimum 0,3 ppm of free chlorine. Preventive application: algae When control is obtained, add a continuous or semi continuous feed of 3 to 5 mg C(M)IT/MIT (3:1) per L of water to be treated - Number and timing of application: Curative application: Bacteria, yeasts and fungi When the system is noticeably fouled, apply 5 to 14,9 mg C(M)IT/MIT (3:1) per Litre of water to be treated, as post treatment after a shock dose of minimum 0,3 ppm of free chlorine. Contact time of 1 hour. Preventive application: algae When control is obtained, add a continuous or semi continuous feed of 3 to 5 mg C(M)IT/MIT (3:1) per L of water to be treated. Regardless of the manner of treatment, the total concentration of the active ingredient C(M)IT/MIT (3:1) in the system should not exceed 14,9 mg/L in the sump water. Preliminary steps prior to addition: The biocidal product is automatically dosed to the system. Manual handling is necessary for the loading of the biocidal product into the dosing systems. Application Frequency: Nominally every 2 to 3 days or as needed to obtain control. Repeat until fouling is reduced to an acceptable level for controlling the microbial growth. |
| Category(ies) of users | industrial |
| Pack sizes and packaging material | For industrial and professional users: — HDPE flask: 5 L (nominal) — HDPE Pail / Jerrycan: 10 L, 20 L, 25 L, 30 L (nominal) — Box with HDPE liner: 20 L — HDPE Drum: 110 L, 120 L, 200 L, 260 L — HDPE IBC: 650 L, 800 L, 1 000 L, 1 250 L All products should be transport and stored in a vented room. |
— Respect the conditions of use of the product (concentration, contact time, temperature, pH, etc.).
— The CMIT/MIT biocidal products are used after a shock dose of free chlorine in this application as standard industry practice.
— Rinse the system (especially the dispensing pumps) with water prior to perform the cleaning step.
— During mixing and loading and cleaning of the dispensing pumps, exposure to the product (corrosive and skin sensitizer product) has to be limited by use of PPE and application of technical and organisational RMM: — Minimisation of manual phases (process automation); — Use of a dosing device; — Regular cleaning of equipment and work area; — Avoidance of contact with contaminated tools and objects; — Good standard of general ventilation; — Training and management of staff on good practice.
— PPE is as follows: — protective chemical resistant gloves (glove material to be specified by the authorisation holder within the product information); — protective coverall (at least type 3 or 4, EN 14605) which is impermeable for the biocidal product shall be worn (coverall material to be specified by the authorisation holder within the product information); — Eye protection; — Substance/task appropriate respirator if ventilation is inadequate.
See general directions for use.
See general directions for use.
See general directions for use.
| Product type | PT04: Food and feed area |
|---|---|
| Where relevant, an exact description of the authorised use | - |
| Target organism(s) (including development stage) | Scientific name: no data Common name: Bacteria Development stage: no data Scientific name: no data Common name: Yeasts Development stage: no data Scientific name: no data Common name: fungi Development stage: no data |
| Field(s) of use | indoor use Preservation of fluids in conveyor belts and pasteurisers The biocidal product is used for the preservation of process fluids in pasteurisers and conveyor belts used in food industry. The biocidal product is used in these systems to either control or kill bacteria and fungi. |
| Application method(s) | Method: closed system Detailed description: Automated dosing The biocidal product is dosed automatically in the heat transfer fluid, in a place of good mixing (e.g. collecting sump below the conveyor belt). |
| Application rate(s) and frequency | Application Rate: Curative application: Bacteria, yeasts and fungi When the system is noticeably fouled, apply 10 to 14,9 g C(M)IT/MIT (3:1) per m3 of water to be treated as post treatment after a shock dose of minimum 0,3 ppm of free chlorine Preventive application: Bacteria: When control is obtained, add a continuous or semi continuous feed of 2,5 to 5 g C(M)IT/MIT (3:1) per m3 of water to be treated. - Number and timing of application: Curative application: Bacteria, yeasts and fungi When the system is noticeably fouled, apply 10 to 14,9 g C(M)IT/MIT (3:1) per m3 of water to be treated as post treatment after a shock dose of minimum 0,3 ppm of free chlorine. Contact time of 1 hour. Preventive application: Bacteria: When control is obtained, add a continuous or semi continuous feed of 2,5 to 5 g C(M)IT/MIT (3:1) per m3 of water to be treated. Preliminary steps prior to addition: The biocidal product is automatically dosed to system. Manual handling is necessary for the loading of containers containing the biocidal product into the dosing systems. Application Frequency: Nominally every 2 to 3 days or as needed to obtain control. Repeat until fouling is reduced to an acceptable level for controlling the microbial growth. |
| Category(ies) of users | industrial |
| Pack sizes and packaging material | For industrial and professional users: — HDPE flask: 5 L (nominal) — HDPE Pail / Jerrycan: 10 L, 20 L, 25 L, 30 L (nominal) — Box with HDPE liner: 20 L — HDPE Drum: 110 L, 120 L, 200 L, 260 L — HDPE IBC: 650 L, 800 L, 1 000 L, 1 250 L All products should be transport and stored in a vented room. |
— Respect the conditions of use of the product (concentration, contact time, temperature, pH, etc.).
— The CMIT/MIT biocidal products are used after a shock dose of free chlorine in this application as standard industry practice.
— Rinse the system (especially the dispensing pumps) with water prior to perform the cleaning step.
— During mixing and loading and cleaning of the dispensing pumps, exposure to the product (corrosive and skin sensitizer product) has to be limited by use of PPE and application of technical and organisational RMM: — Minimisation of manual phases (process automation); — Use of a dosing device; — Regular cleaning of equipment and work area; — Avoidance of contact with contaminated tools and objects; — Good standard of general ventilation; — Training and management of staff on good practice.
— PPE is as follows: — protective chemical resistant gloves (glove material to be specified by the authorisation holder within the product information); — protective coverall (at least type 3 or 4, EN 14605) which is impermeable for the biocidal product shall be worn (coverall material to be specified by the authorisation holder within the product information); — Eye protection; — Substance/task appropriate respirator if ventilation is inadequate.
See general directions for use.
See general directions for use.
See general directions for use.
| Product type | PT04: Food and feed area |
|---|---|
| Where relevant, an exact description of the authorised use | - |
| Target organism(s) (including development stage) | Scientific name: no data Common name: Bacteria Development stage: no data |
| Field(s) of use | indoor use Long term offline preservation of reverse osmosis membranes used in potable water The C(M)IT/MIT (3:1) biocidal product is recommended for controlling biological growth in off-line trains reverse osmosis membranes producing potable water for extended periods of time. |
| Application method(s) | Method: closed system Detailed description: Manual and automated dosing. It is recommended that fouled membranes be cleaned prior to shut-down and preservation. Please refer to RO /NF supplier manual for membrane cleaning and system shutdown procedures. The biocidal product should be dispensed as a tankside additive into the circulating use-dilution of the fluid, using a metering pump or by manual pouring, at a point to assure adequate mixing throughout the system. After complete filling of the trains RO/NF systems with the biocide solution, pumps are stopped (Off line treatment) for extended periods of time. Typically C(M)IT/MIT (3:1) solutions are prepared in the CIP (cleaning in place) tank and added via the dosing system. Dilution with the permeate water or high quality water is recommended for the preparation of the biocide solution. Membranes should be soaked in the biocide solution during the shut-down period. |
| Application rate(s) and frequency | Application Rate: 7,5 -20 g of C(M)IT/MIT (3:1)/ m3 of water - Number and timing of application: 7,5 -20 g of C(M)IT/MIT (3:1)/ m3 of water |
| Category(ies) of users | industrial |
| Pack sizes and packaging material | For industrial and professional users: — HDPE flask: 5 L (nominal) — HDPE Pail / Jerrycan: 10 L, 20 L, 25 L, 30 L (nominal) — Box with HDPE liner: 20 L — HDPE Drum: 110 L, 120 L, 200 L, 260 L — HDPE IBC: 650 L, 800 L, 1 000 L, 1 250 L All products should be transport and stored in a vented room. |
— Respect the conditions of use of the product (concentration, contact time, temperature, pH, etc.).
— Prior to taking the membranes back on-line, flush carefully the elements with permeate water in order to eliminate all the residual biocidal product.
— Rinse the system (especially the dispensing pumps) with water prior to perform the cleaning step.
— During mixing and loading and cleaning of the whole system, exposure to the product (corrosive and skin sensitizer product) has to be limited by use of PPE and application of technical and organisational RMM: — Minimisation of manual phases (process automation); — Use of a dosing device; — Regular cleaning of equipment and work area; — Avoidance of contact with contaminated tools and objects; — Good standard of general ventilation; — Training and management of staff on good practice.
— PPE is as follows: — protective chemical resistant gloves (glove material to be specified by the authorisation holder within the product information); — protective coverall (at least type 3 or 4, EN 14605) which is impermeable for the biocidal product shall be worn (coverall material to be specified by the authorisation holder within the product information); — Eye protection; — Substance/task appropriate respirator if ventilation is inadequate.
See general directions for use.
See general directions for use.
See general directions for use.
| Product type | PT06: Preservatives for products during storage |
|---|---|
| Where relevant, an exact description of the authorised use | - |
| Target organism(s) (including development stage) | Scientific name: no data Common name: Bacteria Development stage: no data Scientific name: no data Common name: Yeasts Development stage: no data |
| Field(s) of use | indoor use outdoor use Preservation of paints and coatings (including electrodeposition) The biocidal product is recommended to control the growth of bacteria and yeasts in coatings applied by an electrodeposition process and associated rinse systems and in water-based paints and coatings in storage containers before use. |
| Application method(s) | Method: closed system Detailed description: Manual and automated dosing. The biocidal product should be dispensed as a tankside additive into the fluid, using a metering pump or by manual pouring, at a point to assure adequate mixing throughout the system. |
| Application rate(s) and frequency | Application Rate: Industrial uses: 1,5 - 14,5 % C(M)IT/MIT in the biocidal products; Professional paints and general public paints: 7,5-14,9 mg/kg C(M)IT/MIT (3:1) in final product. - Number and timing of application: The biocidal product is added at the time of manufacture, storage or shipment. Industrial uses: 1,5 - 14,5 % C(M)IT/MIT in the biocidal products. Professional paints and general public paints: 7,5-14,9 mg/kg C(M)IT/MIT (3:1) in final product. For the biocidal product as supplied: for industrial use only. |
| Category(ies) of users | industrial |
| Pack sizes and packaging material | For industrial and professional users: — HDPE flask: 5 L (nominal) — HDPE Pail / Jerrycan: 10 L, 20 L, 25 L, 30 L (nominal) — Box with HDPE liner: 20 L — HDPE Drum: 110 L, 120 L, 200 L, 260 L — HDPE IBC: 650 L, 800 L, 1 000 L, 1 250 L All products should be transport and stored in a vented room. |
— The preservative can be added at any stage of the production of the product.
— Earliest possible addition is recommended for optimal protection.
— Consult the manufacturer to determine the optimal dosage for the various products to be preserved.
— It is recommended that the optimum biocide concentration and compatibility with individual formulations is determined by means of laboratory tests.
— The duration and storage conditions of the preserved matrices may impact the efficacy of the product, microbiological tests should be conducted to determine the appropriate application rate without exceeding the maximum authorised application rate.
— The biocidal product shall be used for treatment of products (articles/mixtures) distributed to professional users and to the general public.
— During handling phases of products from Meta SPC 1, 2, 3 and 4 (Mixing and Loading), exposure to the product (corrosive and skin sensitizer products) has to be limited by use of PPE and application of technical and organisational RMM: — Minimisation of manual phases (process automation); — Use of a dosing device; — Regular cleaning of equipment and work area; — Avoidance of contact with contaminated tools and objects; — Good standard of general ventilation; — Training and management of staff on good practice.
— PPE is as follows: — protective chemical resistant gloves (glove material to be specified by the authorisation holder within the product information); — protective coverall (at least type 3 or 4, EN 14605) which is impermeable for the biocidal product shall be worn (coverall material to be specified by the authorisation holder within the product information); — Eye protection; — Substance/task appropriate respirator if ventilation is inadequate.
— The maximal concentration of products from Meta SPC 1, 2, 3 and 4 to be added in paints used must be below the threshold value of 15 ppm.
See general directions for use.
See general directions for use.
See general directions for use.
| Product type | PT06: Preservatives for products during storage |
|---|---|
| Where relevant, an exact description of the authorised use | - |
| Target organism(s) (including development stage) | Scientific name: no data Common name: Bacteria Development stage: no data |
| Field(s) of use | indoor use Preservation of fluids used in paper, textile and leather production - The biocidal product is used to reduce contamination by bacteria in textile additives (woven and non-woven, natural and synthetic including silicone emulsions) processing chemicals, all chemicals used in the leather process industry and paper additives (e.g. water pigment pastes, starch, natural gums, synthetic and natural latexes, sizing agents, coating binders, retention aids, dyes, fluorescent whitening agents, wet-strength resins) used in paper mills. The biocidal product inhibits the growth microorganisms, which would otherwise lead to odours formation, viscosity alteration, discolouration of product and premature product failure. |
| Application method(s) | Method: closed system Detailed description: Manual and automated dosing. The biocidal product should be dispensed to the end use fluid at a point to ensure adequate mixing using preferably automated metering pump or by manual addition. |
| Application rate(s) and frequency | Application Rate: Industrial uses: 1,5 - 14,5 % C(M)IT/MIT in the biocidal products; Professional uses: 16 to 30 mg/kg of C(M)IT/MIT (3:1) in final product - Number and timing of application: The biocidal product is added at single dose at time of manufacturing, storage or shipment. Industrial uses: 1,5 - 14,5 % C(M)IT/MIT in the biocidal products. Professional uses: Curative treatment: 16 to 30 mg/kg of C(M)IT/MIT (3:1) in final product Contact time: 24 hours For the biocidal product as supplied: for industrial use only. |
| Category(ies) of users | industrial |
| Pack sizes and packaging material | For industrial and professional users: — HDPE flask: 5 L (nominal) — HDPE Pail / Jerrycan: 10 L, 20 L, 25 L, 30 L (nominal) — Box with HDPE liner: 20 L — HDPE Drum: 110 L, 120 L, 200 L, 260 L — HDPE IBC: 650 L, 800 L, 1 000 L, 1 250 L All products should be transport and stored in a vented room. |
— The preservative can be added at any stage of the production of the product.
— Earliest possible addition is recommended for optimal protection.
— Consult the manufacturer to determine the optimal dosage for the various products to be preserved.
— It is recommended that the optimum biocide concentration and compatibility with individual formulations is determined by means of laboratory tests.
— The duration and storage conditions of the preserved matrices may impact the efficacy of the product, microbiological tests should be conducted to determine the appropriate application rate without exceeding the maximum authorised application rate.
— The biocidal product shall be used for treatment of products (articles/mixtures) distributed only to professional users.
— During handling phases of products from Meta SPC 1, 2, 3 and 4 (mixing and loading), exposure to the product (corrosive and skin sensitizer products) has to be limited by use of PPE and application of technical and organisational RMM: — Minimisation of manual phases (process automation); — Use of a dosing device; — Regular cleaning of equipment and work area; — Avoidance of contact with contaminated tools and objects; — Good standard of general ventilation; — Training and management of staff on good practice.
— PPE is as follows: — protective chemical resistant gloves (glove material to be specified by the authorisation holder within the product information); — protective coverall (at least type 3 or 4, EN 14605) which is impermeable for the biocidal product shall be worn (coverall material to be specified by the authorisation holder within the product information); — Eye protection; — Substance/task appropriate respirator if ventilation is inadequate.
— The maximal products concentration used for the preservation of fluids used in paper, textile and leather production being above the threshold value of 15 ppm, exposure has to be limited by use of PPE protecting skin and mucous membranes potentially exposed and application of technical and organisational RMM: — Minimisation of manual phases; — Use of a dosing device; — Regular cleaning of equipment and work area; — Avoidance of contact with contaminated tools and objects; — Good standard of general ventilation; — Training and management of staff on good practice.
See general directions for use.
See general directions for use.
See general directions for use.
| Product type | PT06: Preservatives for products during storage |
|---|---|
| Where relevant, an exact description of the authorised use | - |
| Target organism(s) (including development stage) | Scientific name: no data Common name: Bacteria Development stage: no data Scientific name: no data Common name: Yeasts Development stage: no data |
| Field(s) of use | indoor use Preservation of glues and adhesives The biocidal product is recommended to control the growth of bacteria and yeasts in water-soluble and water-dispersed synthetic and natural adhesives and tackifiers in storage containers before use |
| Application method(s) | Method: closed system Detailed description: Manual and automated application. The biocidal product should be dispensed to the end use fluid at a point to ensure adequate mixing using preferably automated metering pump or by manual addition. |
| Application rate(s) and frequency | Application Rate: Industrial uses: 1,5 - 14,5 % C(M)IT/MIT in the biocidal products; Professional uses: 8-30 mg/kg C(M)IT/MIT (3:1) in final product. General public uses: 8-14,9 mg/kg C(M)IT/MIT (3:1) in final product. - Number and timing of application: The biocidal product is added at single dose at the time of manufacture, storage or shipment. To ensure uniform distribution, slowly disperse using automated metering or manual addition, into product with agitation. Mix thoroughly until evenly dispersed throughout the product. Industrial uses: 1,5 - 14,5 % C(M)IT/MIT in the biocidal products. Professional uses: 8-30 mg/kg C(M)IT/MIT (3:1) in final product. General public uses: 8-14,9 mg/kg C(M)IT/MIT (3:1) in final product. For the biocidal product as supplied: for industrial use only. |
| Category(ies) of users | industrial |
| Pack sizes and packaging material | For industrial and professional users: — HDPE flask: 5 L (nominal) — HDPE Pail / Jerrycan: 10 L, 20 L, 25 L, 30 L (nominal) — Box with HDPE liner: 20 L — HDPE Drum: 110 L, 120 L, 200 L, 260 L — HDPE IBC: 650 L, 800 L, 1 000 L, 1 250 L All products should be transport and stored in a vented room. |
— The preservative can be added at any stage of the production of the product.
— Earliest possible addition is recommended for optimal protection.
— Consult the manufacturer to determine the optimal dosage for the various products to be preserved.
— It is recommended that the optimum biocide concentration and compatibility with individual formulations is determined by means of laboratory tests.
— The duration and storage conditions of the preserved matrices may impact the efficacy of the product, microbiological tests should be conducted to determine the appropriate application rate without exceeding the maximum authorised application rate.
— The biocidal product shall be used for treatment of products (articles/mixtures) distributed to professional users and to the general public. For products distributed to the general public the maximal concentration used must be below the threshold value of 15 ppm.
— During handling phases of products from Meta SPC 1, 2, 3 and 4 (mixing and loading), exposure to the product (corrosive and skin sensitizer products) has to be limited by use of PPE and application of technical and organisational RMM: — Minimisation of manual phases (process automation); — Use of a dosing device; — Regular cleaning of equipment and work area; — Avoidance of contact with contaminated tools and objects; — Good standard of general ventilation; — Training and management of staff on good practice.
— PPE is as follows: — protective chemical resistant gloves (glove material to be specified by the authorisation holder within the product information); — protective coverall (at least type 3 or 4, EN 14605) which is impermeable for the biocidal product shall be worn (coverall material to be specified by the authorisation holder within the product information); — Eye protection; — Substance/task appropriate respirator if ventilation is inadequate.
— For professional users, the maximal products concentration used for the preservation of glues and adhesives being above the threshold value of 15 ppm, exposure has to be limited by use of PPE, protecting skin and mucous membranes potentially exposed, and application of technical and organisational RMM: — Minimisation of manual phases; — Use of a dosing device; — Regular cleaning of equipment and work area; — Good standard of general ventilation; — Training and management of staff on good practice.
See general directions for use.
See general directions for use.
See general directions for use.
| Product type | PT06: Preservatives for products during storage |
|---|---|
| Where relevant, an exact description of the authorised use | - |
| Target organism(s) (including development stage) | Scientific name: no data Common name: Bacteria Development stage: no data Scientific name: no data Common name: Yeasts Development stage: no data Scientific name: no data Common name: fungi Development stage: no data |
| Field(s) of use | indoor use Preservation of polymer latexes The biocidal product is recommended for the control of bacteria, yeast and fungi in the manufacture, storage, and transport of latexes, synthetic polymers including Hydrolysed Poly Acryl Amide (HPAM) and biopolymers (e.g. xanthan, dextran..) natural latexes. |
| Application method(s) | Method: closed system Detailed description: Manual and automated application. The biocidal product should be dispensed to the end use fluid at a point to ensure adequate mixing using preferably automated metering pump or by manual addition. |
| Application rate(s) and frequency | Application Rate: Industrial uses: 1,5 - 14,5 % C(M)IT/MIT in the biocidal products; Professional uses: 14,9 - 50 mg /kg of C(M)IT/MIT (3:1) in final product. - Number and timing of application: The biocidal product is added at single dose at the time of manufacture, storage or shipment. To ensure uniform distribution, slowly disperse using automated metering or manual addition, into product with agitation. Mix thoroughly until evenly dispersed throughout the product. Industrial uses: 1,5 - 14,5 % C(M)IT/MIT in the biocidal products. Professional uses 14,9 - 50 mg /kg of C(M)IT/MIT (3:1) in final product. For the biocidal product as supplied: for industrial use only. |
| Category(ies) of users | industrial |
| Pack sizes and packaging material | For industrial and professional users: — HDPE flask: 5 L (nominal) — HDPE Pail / Jerrycan: 10 L, 20 L, 25 L, 30 L (nominal) — Box with HDPE liner: 20 L — HDPE Drum: 110 L, 120 L, 200 L, 260 L — HDPE IBC: 650 L, 800 L, 1 000 L, 1 250 L All products should be transport and stored in a vented room. |
— The preservative can be added at any stage of the production of the product.
— Earliest possible addition is recommended for optimal protection.
— Consult the manufacturer to determine the optimal dosage for the various products to be preserved.
— It is recommended that the optimum biocide concentration and compatibility with individual formulations is determined by means of laboratory tests.
— The duration and storage conditions of the preserved matrices may impact the efficacy of the product, microbiological tests should be conducted to determine the appropriate application rate without exceeding the maximum authorised application rate.
— The biocidal product shall be used for treatment of products (articles/mixtures) distributed only to professional users.
— During handling phases of products from Meta SPC 1, 2, 3 and 4 (mixing and loading), exposure to the product (corrosive and skin sensitizer products) has to be limited by use of PPE and application of technical and organisational RMM: — Minimisation of manual phases (process automation); — Use of a dosing device; — Regular cleaning of equipment and work area; — Avoidance of contact with contaminated tools and objects; — Good standard of general ventilation; — Training and management of staff on good practice.
— PPE is as follows: — protective chemical resistant gloves (glove material to be specified by the authorisation holder within the product information); — protective coverall (at least type 3 or 4, EN 14605) which is impermeable for the biocidal product shall be worn (coverall material to be specified by the authorisation holder within the product information); — Eye protection; — Substance/task appropriate respirator if ventilation is inadequate.
— The maximal products concentration used for the preservation of polymer lattices being above the threshold value of 15 ppm, exposure has to be limited by use of PPE, protecting skin and mucous membranes potentially exposed, and application of technical and organisational RMM: — Minimisation of manual phases; — Use of a dosing device; — Regular cleaning of equipment and work area; — Good standard of general ventilation; — Training and management of staff on good practice.
See general directions for use.
See general directions for use.
See general directions for use.
| Product type | PT06: Preservatives for products during storage |
|---|---|
| Where relevant, an exact description of the authorised use | - |
| Target organism(s) (including development stage) | Scientific name: no data Common name: Bacteria Development stage: no data |
| Field(s) of use | indoor use Preservation of mineral slurries The biocidal product is recommended to control the growth of bacteria in aqueous-based inorganic/mineral slurries and inorganic pigments which are formulated into paints, coatings and paper. |
| Application method(s) | Method: closed system Detailed description: Manual and automated application. The biocidal product should be dispensed as a tankside additive into the circulating use-dilution of the fluid, using a metering pump or by manual pouring, at a point to assure adequate mixing throughout the system. |
| Application rate(s) and frequency | Application Rate: Industrial uses: 1,5 - 14,5 % C(M)IT/MIT in the biocidal products; Professional uses: 10- 30 mg/kg of C(M)IT/MIT (3:1) in final product. - Number and timing of application: The biocidal product is added at single dose at the time of manufacture, storage or shipment. Industrial uses: 1,5 - 14,5 % C(M)IT/MIT in the biocidal products. Professional uses: 10- 30 mg/kg of C(M)IT/MIT (3:1) in final product. For the biocidal product as supplied: for industrial use only. |
| Category(ies) of users | industrial |
| Pack sizes and packaging material | For industrial and professional users: — HDPE flask: 5 L (nominal) — HDPE Pail / Jerrycan: 10 L, 20 L, 25 L, 30 L (nominal) — Box with HDPE liner: 20 L — HDPE Drum: 110 L, 120 L, 200 L, 260 L — HDPE IBC: 650 L, 800 L, 1 000 L, 1 250 L All products should be transport and stored in a vented room. |
— The preservative can be added at any stage of the production of the product.
— Earliest possible addition is recommended for optimal protection.
— Consult the manufacturer to determine the optimal dosage for the various products to be preserved.
— It is recommended that the optimum biocide concentration and compatibility with individual formulations is determined by means of laboratory tests.
— The duration and storage conditions of the preserved matrices may impact the efficacy of the product, microbiological tests should be conducted to determine the appropriate application rate without exceeding the maximum authorised application rate.
— The biocidal product shall be used for treatment of products (articles/mixtures) distributed only to professional users.
— During handling phases of products from Meta SPC 1, 2, 3 and 4 (mixing and loading), exposure to the product (corrosive and skin sensitizer products) has to be limited by use of PPE and application of technical and organisational RMM: — Minimisation of manual phases (process automation); — Use of a dosing device; — Regular cleaning of equipment and work area; — Avoidance of contact with contaminated tools and objects; — Good standard of general ventilation; — Training and management of staff on good practice.
— PPE is as follows: — protective chemical resistant gloves (glove material to be specified by the authorisation holder within the product information); — protective coverall (at least type 3 or 4, EN 14605) which is impermeable for the biocidal product shall be worn (coverall material to be specified by the authorisation holder within the product information); — Eye protection; — Substance/task appropriate respirator if ventilation is inadequate.
The maximal products concentration used for the preservation of mineral slurries being above the threshold value of 15 ppm, exposure has to be limited by use of PPE, protecting skin and mucous membranes potentially exposed, and application of technical and organisational RMM:
— Minimisation of manual phases;
— Use of a dosing device;
— Regular cleaning of equipment and work area;
— Good standard of general ventilation;
— Training and management of staff on good practice.
See general directions for use.
See general directions for use.
See general directions for use.
| Product type | PT06: Preservatives for products during storage |
|---|---|
| Where relevant, an exact description of the authorised use | - |
| Target organism(s) (including development stage) | Scientific name: no data Common name: Bacteria Development stage: no data Scientific name: no data Common name: Yeasts Development stage: no data |
| Field(s) of use | indoor use Preservation of building (construction) products (including sealants, caulks, plasters etc.) The biocidal product is recommended to control the growth of bacteria in building (construction) products (sealants, caulks, biopolymers, plasters, fillers, admixtures concrete additives, joints compounds,..). |
| Application method(s) | Method: - Detailed description: Manual and automated dosing. The biocidal product should be dispensed to the end use fluid at a point to ensure adequate mixing using preferably automated metering pump or by manual addition. |
| Application rate(s) and frequency | Application Rate: Industrial uses: 1,5 - 14,5 % C(M)IT/MIT in the biocidal products; Professional uses: Add at typical use rate between 16,2-30 mg C(M)IT/MIT (3:1) per Kg final product to be treated. - Number and timing of application: The biocidal product is added at single dose at the time of manufacture, storage or shipment. Slowly dispense using automated metering or manually. Mix thoroughly until the biocidal product is evenly dispersed. Industrial uses: 1,5 - 14,5 % C(M)IT/MIT in the biocidal products. Professional uses: Add at typical use rate between 16,2-30 mg C(M)IT/MIT (3:1) per Kg final product to be treated. For the biocidal product as supplied: for industrial use only. |
| Category(ies) of users | industrial |
| Pack sizes and packaging material | For industrial and professional users: — HDPE flask: 5 L (nominal) — HDPE Pail / Jerrycan: 10 L, 20 L, 25 L, 30 L (nominal) — Box with HDPE liner: 20 L — HDPE Drum: 110 L, 120 L, 200 L, 260 L — HDPE IBC: 650 L, 800 L, 1 000 L, 1 250 L All products should be transport and stored in a vented room. |
— The preservative can be added at any stage of the production of the product.
— Earliest possible addition is recommended for optimal protection.
— Consult the manufacturer to determine the optimal dosage for the various products to be preserved.
— It is recommended that the optimum biocide concentration and compatibility with individual formulations is determined by means of laboratory tests.
— The duration and storage conditions of the preserved matrices may impact the efficacy of the product, microbiological tests should be conducted to determine the appropriate application rate without exceeding the maximum authorised application rate.
— The biocidal product shall be used for treatment of products (articles/mixtures) distributed only to professional users.
— This use is restricted to the preservation of building material applied indoor only.
— During handling phases for products from Meta SPC 1, 3 and 4 (mixing and loading), exposure to the product (corrosive and skin sensitizer products) has to be limited by use of PPE and application of technical and organisational RMM: — Minimisation of manual phases (process automation); — Use of a dosing device; — Regular cleaning of equipment and work area; — Avoidance of contact with contaminated tools and objects; — Good standard of general ventilation; — Training and management of staff on good practice.
— PPE is as follows: — protective chemical resistant gloves (glove material to be specified by the authorisation holder within the product information); — protective coverall (at least type 3 or 4, EN 14605) which is impermeable for the biocidal product shall be worn (coverall material to be specified by the authorisation holder within the product information); — Eye protection; — Substance/task appropriate respirator if ventilation is inadequate.
For professional users, the maximal products concentration used for the preservation of building products being above the threshold value of 15 ppm, exposure has to be limited by use of PPE, protecting skin and mucous membranes potentially exposed, and application of technical and organisational RMM:
— Minimisation of manual phases;
— Regular cleaning of equipment and work area;
— Good standard of general ventilation;
— Training and management of staff on good practice.
See general directions for use.
See general directions for use.
See general directions for use.
| Product type | PT06: Preservatives for products during storage |
|---|---|
| Where relevant, an exact description of the authorised use | - |
| Target organism(s) (including development stage) | Scientific name: no data Common name: Bacteria Development stage: no data Scientific name: no data Common name: Yeasts Development stage: no data |
| Field(s) of use | indoor use Preservation of inks The biocidal product is recommended to control the growth of bacteria and yeasts in inks and ink components (printing inks lithographic, photographic, ink-jet fluids, water based dampening or fountain solutions inks used for textile printing). The biocidal product inhibits the growth of microorganisms, which would otherwise lead to odour formation, viscosity alteration, product discolouration and premature product failure. |
| Application method(s) | Method: closed system Detailed description: Manual and automated dosing. The biocidal product should be dispensed to the end use fluid at a point to ensure adequate mixing using preferably automated metering pump or by manual addition. |
| Application rate(s) and frequency | Application Rate: Industrial uses: 1,5 - 14,5 % C(M)IT/MIT in the biocidal products. Professional uses: 6-30 mg C(M)IT/MIT (3:1) /kg final product. General public uses: 6-14,9 mg C(M)IT/MIT (3:1) /kg final product. - Number and timing of application: The biocidal product is added at single dose at time of manufacturing, storage or shipment. Industrial uses: 1,5 - 14,5 % C(M)IT/MIT in the biocidal products. Professional uses: 6-30 mg C(M)IT/MIT (3:1) /kg final product. General public uses: 6-14,9 mg C(M)IT/MIT (3:1) /kg final product. For the biocidal product as supplied: for industrial use only. |
| Category(ies) of users | industrial |
| Pack sizes and packaging material | For industrial and professional users: — HDPE flask: 5 L (nominal) — HDPE Pail / Jerrycan: 10 L, 20 L, 25 L, 30 L (nominal) — Box with HDPE liner: 20 L — HDPE Drum: 110 L, 120 L, 200 L, 260 L — HDPE IBC: 650 L, 800 L, 1 000 L, 1 250 L All products should be transport and stored in a vented room. |
— The preservative can be added at any stage of the production of the product.
— Earliest possible addition is recommended for optimal protection.
— Consult the manufacturer to determine the optimal dosage for the various products to be preserved.
— It is recommended that the optimum biocide concentration and compatibility with individual formulations is determined by means of laboratory tests.
— The duration and storage conditions of the preserved matrices may impact the efficacy of the product, microbiological tests should be conducted to determine the appropriate application rate without exceeding the maximum authorised application rate.
— The biocidal product shall be used for treatment of products (articles/mixtures) distributed to professional users and to the general public. For products distributed to the general public the maximal concentration used must be below the threshold value of 15 ppm.
— During handling phases of products from Meta SPC 1, 2, 3 and 4 (mixing and loading), exposure to the product (corrosive and skin sensitizer products) has to be limited by use of PPE and application of technical and organisational RMM: — Minimisation of manual phases (process automation); — Use of a dosing device; — Regular cleaning of equipment and work area; — Avoidance of contact with contaminated tools and objects; — Good standard of general ventilation; — Training and management of staff on good practice.
Reading this document does not replace reading the official text published in the Official Journal of the European Union. We assume no responsibility for any inaccuracies arising from the conversion of the original to this format.
This text is published under EUR-Lex's own terms of reuse, not a Legalize or public-domain licence.
EUR-Lex
Creative Commons Attribution 4.0 International (CC BY 4.0)
© European Union, https://eur-lex.europa.eu — Source: EUR-Lex (Publications Office of the European Union). Reused under the Creative Commons Attribution 4.0 International (CC BY 4.0) licence. Only EU legislation published in the printed Official Journal of the European Union is deemed authentic; consolidated texts are reproduced here for documentation purposes and have been reformatted to Markdown.